Search for large spray paint booth, water wash booth or conveyorised painting booth and you will find three overlapping but distinct ideas. A large spray booth is about size - oversized components like buses, trucks and rail coaches. A water wash paint booth is about overspray capture method - a falling water curtain instead of dry filters. A conveyorised booth is about production flow - parts moving continuously instead of batch loading. Many large industrial paint shops in India combine all three. This guide covers each on its own and where they meet. For the products themselves, see our large paint booth page, water wash booth page and conveyorised plant page.
📋 What This Guide Covers
- Three different ideas, one guide
- How a water wash (water curtain) booth works
- Sizing a large spray paint booth
- Conveyorised booths for continuous production
- Water wash vs dry filtration: which to choose
- Chemicals, sludge and water management
- Maintenance checklist
- Where these booths are used in India
- Cost and what drives it
- Buyer checklist
1. Three different ideas, one guide
Before comparing options, it helps to separate what each term actually describes:
- Large spray paint booth: internal working dimensions exceeding roughly 6 x 4 x 4 metres - sized for buses, trucks, railway coaches, structural steel, marine craft or oversized industrial machinery.
- Water wash / water paint booth: an overspray-capture method using a falling water curtain instead of dry filter media - independent of booth size.
- Conveyorised painting booth: a production-flow design where parts move continuously through pretreatment, booth and oven on an overhead chain conveyor, instead of batch loading.
A booth can be large and water wash and conveyorised at the same time - or any single one of the three. The right combination depends on component size, paint volume and whether production is continuous or batch.
2. How a water wash (water curtain) booth works
A water wash booth has a continuously falling sheet of water at the rear wall. Four things happen in sequence:
- Capture: paint overspray hits the falling water sheet and bonds to it instead of drifting into the exhaust duct or settling on the booth walls.
- De-tackification: dosed chemicals - de-tackifiers, defoamers, biocides and pH-adjusters - coagulate the paint into a floating sludge rather than a sticky residue.
- Settling: sludge floats to the top of the tank and is skimmed off; cleaner water continues to recirculate.
- Exhaust: air that has passed through the water curtain rises through a mist eliminator before being exhausted, removing water droplets from the airstream.
Because the chemistry and water do the capture work rather than replaceable filter media, this design suits booths that run continuously or paint high volumes - the kind of duty cycle where dry filters would need very frequent replacement.
3. Sizing a large spray paint booth
Autocoat classes a booth as "large" once internal dimensions pass about 6 x 4 x 4 metres, and has built booths up to 22 metres long, 5 metres wide and 5 metres high for railway coach manufacturers, defence vehicle painters and large bus body builders - there is no fixed upper limit beyond what the site and application call for.
Large booths need more than just floor space:
- Roof clearance: at least 1.5 m above the booth roof for ducting, exhaust and lighting; total clear height can reach 7-8 m for tall railway coach booths.
- Airflow design: multiple intake plenums and blower banks distributed along the booth length, with computational airflow modelling to avoid dead zones, and multi-zone controls so operators can tune flow per section.
- Multi-station working: large booths can be split into 2-3 working stations with partitions or curtains, so prep, primer, base and topcoat can run in different zones at once.
4. Conveyorised booths for continuous production
A conveyorised painting booth replaces batch loading with a continuous overhead chain conveyor that carries parts through pretreatment, the spray or powder booth, and the bake oven without stopping. SME-scale lines are typically sized for 200 to 500 parts per shift, handling components up to about 600 x 600 x 900 mm and 25-50 kg per hook, at a chain speed of roughly 0.5 to 1.5 m/min.
The most common layout is linear or U-shaped: load → pretreatment (5 or 7 tanks) → drying-off oven → paint or powder booth → curing oven → cooling zone → unload. The U-shape lets a single operator handle both loading and unloading. A typical floor footprint is 25-40 sq m, with a 30-60 m conveyor track.
Businesses that move from manual batch painting to a conveyorised line typically see a 3-5x throughput improvement, with payback generally in the 18-30 month range depending on utilisation.
5. Water wash vs dry filtration: which to choose
| Factor | Water wash booth | Dry filter booth |
|---|---|---|
| Best suited to | High paint volume, continuous shifts, large components | Moderate volume, intermittent or mixed production |
| Consumable replacement | Chemical dosing + periodic sludge removal | Filter media replaced on schedule |
| Downtime for consumable change | Low - dosing is continuous | Booth typically stops to change filters |
| Water/chemical handling | Recirculating tank, sludge skimming, PCB-compliant disposal | None |
| Typical applications | Buses, trucks, railway coaches, structural steel, marine | Automotive refinish, general industrial, mixed small parts |
Neither option is universally "better" - the choice follows paint volume, component size and how much filter-change downtime your production schedule can absorb.
6. Chemicals, sludge and water management
A water wash booth needs ongoing chemical and water management, not just plumbing:
- Chemicals: de-tackifiers, defoamers, biocides and pH-adjusters, dosed automatically to keep paint coagulating correctly and prevent foaming or bacterial growth.
- Paint load: a standard water-screen booth handles roughly 10-100 litres of paint per shift; above that, a dedicated Auto Paint Sludge Remover and a sedimentation pit are recommended.
- Water top-up: because the water recirculates, daily top-up is only to replace evaporation - typically 50-200 litres per shift.
- Tank life and clean-out: with proper dosing, tank water generally lasts 4-8 weeks before a full drain and recharge; sludge skimming and disposal through PCB-approved hazardous waste handlers is typically a monthly task.
7. Maintenance checklist
Routine checks
- Daily: water level, chemical dosing rate and pump pressure
- Weekly: skim floating sludge, clean strainers and nozzles
- Monthly: drain and recharge the water tank
- Annually: inspect FRP lining, impellers and mist eliminators
For a conveyorised line, add conveyor chain lubrication, hook and carrier inspection, and oven insulation checks to this schedule.
8. Where these booths are used in India
Large, water wash and conveyorised designs - alone or combined - cover a wide span of Indian manufacturing:
- Bus and truck body builders painting large panels with high paint throughput
- Railway coach and rolling-stock manufacturers needing very large booths with multi-zone airflow
- Structural steel and heavy engineering fabricators with oversized, irregular components
- SME component manufacturers - fan motors, electrical panels, two-wheeler frames, agricultural parts - running conveyorised lines at 200-500 parts/shift
9. Cost and what drives it
Autocoat does not publish a fixed price because cost depends on:
- Booth internal size and number of airflow zones
- Water-wash tank volume, pump power and chemical dosing system (if water wash)
- Conveyor length, chain speed and automation level (if conveyorised)
- Filtration grade, lighting, heating/bake integration
- FRP lining and civil work for the water tank or pit
Send your component size, production volume and whether you need water wash, conveyorised operation, or both, for an exact quotation. See our paint booth price guide for how booth pricing is generally structured.
10. Buyer checklist
Before you order
- Largest component size and shift-wise production volume
- Paint volume per shift - under or over roughly 100 litres
- Continuous conveyorised flow needed, or batch loading acceptable
- Site space for a water tank/pit if choosing water wash
- Roof clearance and civil work for a large booth
- Effluent/sludge disposal arrangement confirmed with a PCB-approved handler
- Commissioning tests: airflow survey, water/chemical dosing check, trial spray run
Planning a Large, Water Wash or Conveyorised Booth?
Send your component size, paint volume and production flow (batch or continuous). Autocoat's engineers will recommend the right combination and send a budget quotation.
Get Free Quote →Frequently Asked Questions
What is a water wash spray booth?
A booth with a continuously falling water curtain that captures overspray. Chemicals neutralise the paint, clean air exits through a mist eliminator, and sludge settles in a trough.
What qualifies as a large spray paint booth?
Internal dimensions exceeding about 6 x 4 x 4 m - sized for buses, trucks, railway coaches and oversized machinery. Autocoat has built up to 22 x 5 x 5 m.
What is a conveyorised painting booth?
A booth where parts move continuously on an overhead chain conveyor through pretreatment, booth and oven. SME lines typically run 200-500 parts per shift.
Why choose water wash over dry filtration?
Water wash suits high paint volumes, continuous shifts and large components where dry-filter downtime is costly. Dry filtration suits lower or intermittent volumes.
How is sludge handled in a water wash booth?
Sludge floats and is skimmed into a trolley, dewatered and disposed through a PCB-approved handler. Tank water typically lasts 4-8 weeks between full clean-outs.
How much water does a water wash booth use?
Recirculating water only needs evaporation top-up - typically 50-200 litres/shift. Paint load is usually 10-100 litres/shift for a standard booth.
How big can a conveyorised line be built?
SME-scale plants typically run a 25-40 sq m footprint and 30-60 m conveyor track, handling parts up to 600x600x900 mm and 25-50 kg per hook.
What does a large or water wash booth cost?
Depends on size, water-wash and chemical dosing system, conveyor length and automation. Send component size and volume for an exact quotation.
How long does a large paint booth take to install?
About 4-6 weeks on site once civil work is ready, with 8-12 weeks manufacturing lead time running in parallel.
